Analytica, Volume 4, Issue 4 (December 2023) – 8 articles

Marine algae are a valuable source of polysaccharides. However, the information available on sulfated polysaccharides from microalgae is limited. Navicula sp. is a microalga present in the Sea of Cortez, of which little is known regarding their polysaccharides’ properties. This study investigated the physicochemical and microstructural characteristics of Navicula sp. sulfated polysaccharide (NSP). The Fourier transform infrared spectrum of NSP showed distinctive bands (1225 and 820 cm⁻¹, assigned to S–O and C–O–S stretching, respectively), confirming the molecular identity. NSP registered molecular weight, intrinsic viscosity, a radius of gyration, and a hydrodynamic radius of 1650 kDa, 197 mL/g, 61 nm, and 36 nm, respectively. The zeta potential, electrophoretic mobility, conductivity, and diffusion coefficient of the molecule were −5.8 mV, −0.45 µm cm/s V, 0.70 mS/cm, and 2.9 × 10⁻⁹ cm²/s, respectively. The characteristic ratio and persistence length calculated for NSP were 4.2 and 1.3 nm, suggesting a nonstiff polysaccharide chain conformation. The Mark–Houwink–Sakurada α and K constants were 0.5 and 1.67 × 10⁻¹, respectively, indicating a molecular random coil structure. NSP scanning electron microscopy revealed a rough and porous surface. Knowing these polysaccharides’ physicochemical and microstructural characteristics can be the starting point for elucidating their structure–function relationship as a valuable tool in advanced biomaterial design. Full article

This work developed a conductive ink composed of carbonaceous material for printing electrochemical sensors. The optimized ink comprises graphite, carbon black, and nail polish, respectively (35.3:11.7:53%), as well as acetone as a solvent. The proportion was optimized with consideration of the binder’s solubilization, the ink’s suitability for the screen-printing process, and lower electrical resistance. The materials used, and the resulting ink, were analyzed by way of Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), Raman spectroscopy, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). The charge transfer resistance (Rct) obtained was 0.348 kΩ. The conductive ink was used to print an electrode on a PET substrate, and a flexible and disposable electrode was obtained. The electroactive area obtained was 13.7 cm², which was calculated by the Randles-Sevcik equation. The applicability of the device was demonstrated with a redox probe, providing a sensitivity of 0.02 µ A L mmol⁻¹. The conductive ink has adequate homogeneity for producing electrodes using the screen-printing technique, with a low estimated production cost of $ 0.09 mL⁻¹. Full article

Argan kernels, fruits regurgitated by goats, are 30% cheaper than the regular kernels used to prepare food argan oil. The use of such argan kernels as a cosmetic ingredient, after refining, is thus economically attractive. The oxidative stability of argan oil prepared from sub-quality kernels is not known. In the present paper, the physicochemical quality, oxidative stability indices, and bioactive compounds of refined argan oil (RAO) obtained from sub-quality kernels and virgin argan oil (VAO) were compared and evaluated over a period of storage of 12 weeks at 60 °C. Quality parameters consisted of free fatty acids (FFAs), peroxide value (PV), p-anisidine value (p-AV), UV extinction coefficients (K232 and K270), total oxidation, iodine and saponification values, induction time, fatty acid composition, and tocopherol content. Our outcomes reveal that the combined effects of refining and storage generally resulted in high values of the routinely measured quality indices, including FFA, p-AV, K270, K232, and PV. Likewise, refining reduced the levels of individual tocopherols and unsaturated fatty acids (USFAs) but increased saturated fatty acids (SFAs). Similar trends were observed under storage with decreased levels of tocopherols and high SFA for both RAO and VAO. Storage also resulted in an increased level of USFAs in the case of RAO but not in VAO. The obtained results show that RAO was more sensitive to oxidation than VAO. At room temperature, RAO had a shorter induction time of six months, implying that RAO will have a shorter shelf life compared to VAR. Thus, such instability means that the refining process for argan oil must be carried out with great care, and this oil needs to be protected once refined. Full article

Optical detection devices have become an analytical tool of interest in diverse fields of science. The search for methods to identify and quantify different compounds has transposed this curiosity into a necessity, since some constituents threaten the safety of life in all its forms. In this context, 30 years ago, Prof. Prasanna de Silva presented the idea of sensors as Molecular Logic Gates (MLGs): a molecule that performs a logical operation based on one or more inputs (analytes) resulting in an output (optical modification such as fluorescence or absorption). In this review, we explore the implementation of MLGs based on the interference of a second input (second analyte) in suppressing or even blocking a first input (first analyte), often resulting in INHIBIT-type gates. This approach is interesting because it is not related to attached detecting groups in the MLG but to the relation between the first and the second input. In this sense, flexible and versatile MLGs can be straightforwardly designed based on input selection. To illustrate these cases, we selected examples seeking to diversify the inputs (first analytes and interfering analytes), outputs (turn on, turn off), optical response (fluorescent/colorimetric), and applicability of these MLGs. Full article

Chemical ultraviolet filters are widely used in a variety of cosmetic products to protect the skin from the harmful effects of UV radiation. In order to guarantee consumers’ health, the content in sunscreens is regulated in a number of countries. Many analytical methods are used to determine UV filters in cosmetics samples. In recent years, attention has been paid to the fact that the methods should have a small impact on the environment. This work examined the greenness of 10 reported chromatographic methods in the literature for the determination of UV filters in cosmetic samples using two new tools: analytical greenness metric (AGREE) and analytical greenness metric for sample preparation (AGREEprep). Microextraction methods of sample preparation in the AGREEprep assessment show a higher score of greenness. The results recommended the use of both tools to assess the greening of methods before planning laboratory analytical methods to measure their ecological impact on the environment. Full article

A novel Eu(tta)₃([4,4′-(t-bu)₂-2,2′-bpy)] complex (tta-thenoyltrifluoroacetone), a ratiometric luminescent-based optical sensor for the quantitative determination of aluminum ion, is synthesized and characterized using XRD and ¹H NMR. The XRD data reveal the slightly distorted octahedral structure. The complex displays a bright red emission at 613 nm in methanol which is characteristic of europium (III) complexes. Upon the addition of Al³⁺ ions, the red emission disappears, and a new blue emission at 398 nm emerges, manifesting the ratiometric nature of the complex. The turn-off of the red emission and turn-on of the blue emission are attributed to Eu-Al trans-metalation, as supported by Raman data that show the emergence of Al-O vibrations at 418, 495, and 608 cm⁻¹ concomitant with the disappearance of Eu-O and Eu-N bond vibrations. Most aluminum sensors are known to suffer from interferences from other metals including Cu²⁺, Co²⁺, and Cd²⁺. However, the sensor reported here is tested for 11 common cations and shows no interference on sensitivity. To the best of our knowledge, this is the first known Eu-based luminescence sensor that successfully exhibited the ability to detect aluminum ions in ppb levels in aqueous environments. The calculated Al³⁺ binding constant is 2.496 × 10³ ± 172. The complex shows a linear relationship in the range of 0–47.6 ppb (1.76 × 10⁻⁶ M) Al³⁺ and the limit of detection (LOD) is 4.79 ppb (1.77 × 10⁻⁷ M) in MeOH. ICP-OES is used for validation of the sensor complex in water and then it was used for quantitative detection of Al³⁺ ions in water as a real-life application. The complex can accurately detect Al³⁺ ions in the range of 4.97–24.9 ppb (1.84 × 10⁻⁷ M–9.2 × 10⁻⁷ M) with an LOD of 8.11 ppb (2.99 × 10⁻⁷ M). Considering that the aluminum ion serves no recognized function within the human body, its accumulation can lead to severe neurological disorders, including Parkinson’s and Alzheimer’s diseases. With the LOD value significantly lower than the WHO-recommended maximum permissible level of 200 ppb for aluminum in drinking water, even without high-power laser-aided signal enhancement, the sensor shows promise for detecting trace amounts of aluminum contamination in water. Therefore, it can significantly aid in the monitoring of even the smallest aluminum ion contamination in drinking water, industrial effluents, and natural water bodies. Full article

Gold nanoclusters are peculiar objects promising in view of qualitative and quantitative determination of various species, including heavy metal ions and biological molecules. We have recently discovered that introducing sodium azide in the reaction mixture during gold nanocluster synthesis in the presence of citrate and adenosine monophosphate can tune the product emission from blue to yellow. Taking advantage of the factorial design of the experiment, we have optimized the synthesis conditions to obtain pure blue and yellow emitters and investigate their sensitivity to a series of inorganic salts. The experiments have revealed selective quenching of the nanocluster’s fluorescence in the presence of mercury(II) ions. Full article

The incidence of colorectal cancer (CRC) is increasing worldwide. It has variable signs and symptoms starting from changes in bowel habit to nausea and vomiting. Chemotherapeutic agents are often prescribed in CRC such as Capecitabine (CCB) and 5-Fluorouracil (FU). CCB is the prodrug of FU in oral dosage form, which makes it preferable by physicians, since no hospitalization is needed for drug administration. CCB is activated to FU in a three-step reaction producing 5′-deoxy-5-fluorocytidine (DFCR) (by carboxylesterase (CES) enzyme), then 5′-deoxy-5-fluorouridine (DFUR) (by cytidine deaminase (CDD) enzyme) and finally FU (by thymidine phosphorylase (TP) enzyme), the active form, which is later deactivated to give 5,6-dihydro-5-fluorouracil (DHFU). Different patients exhibit variable drug responses and adverse in response to CCB therapy, despite being treated by the same dose, which could be attributed to the occurrence of different possible enzyme single nucleotide polymorphisms (SNPs) along the activation and deactivation pathways of CCB. The most commonly occurring toxicities in CCB therapy are hand-foot syndrome and diarrhea. This study aims at developing and validating a new method for the simultaneous determination of CCB and its metabolites by HPLC-UV, followed by a correlation study with the toxicities occurring during therapy, where predictions of toxicity could be based on metabolites’ levels instead of the tedious process of genotyping. A new superior analytical method was optimized by a quality-by-design approach using DryLab^® 2000 software achieving a baseline resolution of the six analytes within the least possible gradient time of 10 min. The method also showed linearity (in a range from 1 to 500 μg/mL), accuracy, precision and robustness upon validation: The LOD was found to be 3.0 ng/mL for DHFU and CCB, and 0.3 ng/mL for DFUR, DFCR and FU. The LOQ was found to be 10.0 ng/mL for DHFU and CCB, and 1.0 ng/mL for DFUR, DFCR and FU. The clinical results showed a positive correlation between the concentration of DFCR and mucositis and between the concentration of DFUR and hand-foot syndrome, confirming that this technique could be used for predicting such toxicities. Full article