Journal Description
Journal of Manufacturing and Materials Processing
Journal of Manufacturing and Materials Processing
is an international, peer-reviewed, open access journal on the scientific fundamentals and engineering methodologies of manufacturing and materials processing published bimonthly online by MDPI.
- Open Access— free for readers, with article processing charges (APC) paid by authors or their institutions.
- High Visibility: indexed within Scopus, ESCI (Web of Science), Inspec, CAPlus / SciFinder, and other databases.
- Journal Rank: CiteScore - Q1 (Mechanical Engineering)
- Rapid Publication: manuscripts are peer-reviewed and a first decision is provided to authors approximately 14.2 days after submission; acceptance to publication is undertaken in 2.9 days (median values for papers published in this journal in the second half of 2023).
- Recognition of Reviewers: reviewers who provide timely, thorough peer-review reports receive vouchers entitling them to a discount on the APC of their next publication in any MDPI journal, in appreciation of the work done.
Impact Factor:
3.2 (2022);
5-Year Impact Factor:
3.6 (2022)
Latest Articles
Numerical Modeling of Cutting Characteristics during Short Hole Drilling: Part 2—Modeling of Thermal Characteristics
J. Manuf. Mater. Process. 2024, 8(1), 13; https://doi.org/10.3390/jmmp8010013 - 13 Jan 2024
Abstract
The modeling of machining process characteristics and, in particular, of various cutting processes occupies a significant part of modern research. Determining the thermal characteristics in short hole drilling processes by numerical simulation is the object of the present study. For different contact conditions
[...] Read more.
The modeling of machining process characteristics and, in particular, of various cutting processes occupies a significant part of modern research. Determining the thermal characteristics in short hole drilling processes by numerical simulation is the object of the present study. For different contact conditions of the workpiece with the drill cutting inserts, the thermal properties of the machined material were determined. The above-mentioned properties and parameters of the model components were established using a three-dimensional finite element model of orthogonal cutting. Determination of the generalized values of the machined material thermal properties was performed by finding the set intersection of individual properties values using a previously developed software algorithm. A comparison of experimental and simulated values of cutting temperature in the workpiece points located at different distances from the drilled hole surface and on the lateral clearance face of the drill outer cutting insert shows the validity of the developed numerical model for drilling short holes. The difference between simulated and measured temperature values did not exceed 22.4% in the whole range of the studied cutting modes.
Full article
(This article belongs to the Special Issue Advances in High-Performance Machining Operations)
►
Show Figures
Open AccessArticle
Assessing the Feasibility of Fabricating Thermoplastic Laminates from Unidirectional Tapes in Open Mold Environments
by
, , , , , and
J. Manuf. Mater. Process. 2024, 8(1), 12; https://doi.org/10.3390/jmmp8010012 - 06 Jan 2024
Abstract
The automation of the manufacturing processes of thermoplastic composite laminates has become dependent on open mold processes such as automated tape placement (ATP), which couples tape layering with in situ consolidation. The manufacturing parameters of ATP open mold processes, which comprise processing time,
[...] Read more.
The automation of the manufacturing processes of thermoplastic composite laminates has become dependent on open mold processes such as automated tape placement (ATP), which couples tape layering with in situ consolidation. The manufacturing parameters of ATP open mold processes, which comprise processing time, consolidation pressure and temperature, affect the bond strength between the plies and the quality of the laminates produced. Therefore, the effect of the manufacturing parameters should be characterized. This work experimentally evaluates the feasibility of fabricating thermoplastic laminates using an open mold process that reasonably models that of ATP. Glass fiber-reinforced polypropylene laminates are fabricated from unidirectional tapes under different consolidation periods, pressures, and temperatures. The bond quality in the produced laminates is assessed by measuring their interlaminar shear strength, which is measured using a short beam standardized shear test in conjunction with digital image correlation. Results show that consolidation can occur at temperatures slightly below the composite tapes’ complete melting temperature, and consolidation times between 7 and 13 min can result in acceptable bond strengths. The results confirmed the feasibility of the process and highlighted its limitations. Analysis of variance and machine learning showed that the effect of process parameters on interlaminar shear strength is nonlinear.
Full article
(This article belongs to the Special Issue Manufacturing Process Development of Advanced Composite Materials)
►▼
Show Figures
Figure 1
Open AccessArticle
Vickers Hardness Mechanical Models and Thermoplastic Polymer Injection-Molded Products’ Static Friction Coefficients
J. Manuf. Mater. Process. 2024, 8(1), 11; https://doi.org/10.3390/jmmp8010011 - 05 Jan 2024
Abstract
►▼
Show Figures
The surface mechanical properties of thermoplastics are crucially important for evaluating molded products’ vulnerability to scratching. Because surface mechanical properties reflect material performance directly in terms of durability and frictional behavior, understanding and modeling them is important for industry and research. This emphasizes
[...] Read more.
The surface mechanical properties of thermoplastics are crucially important for evaluating molded products’ vulnerability to scratching. Because surface mechanical properties reflect material performance directly in terms of durability and frictional behavior, understanding and modeling them is important for industry and research. This emphasizes the surface mechanical properties of Vickers hardness and the static friction coefficient, with attempts to model them as functions of stress at yield initiation. Vickers hardness can be related to the compressive stress at yield initiation. The static friction coefficient can be modeled as a function of the surface shear strength and Vickers hardness. This research has improved our understanding of thermoplastics’ surface mechanical properties and has enabled the prediction of the scratch performance of molded products and the provision of effective indicators for material design.
Full article
Figure 1
Open AccessCommunication
Phase Composition, Microstructure and Mechanical Properties of Zr57Cu15Ni10Nb5 Alloy Obtained by Selective Laser Melting
by
, , , , and
J. Manuf. Mater. Process. 2024, 8(1), 10; https://doi.org/10.3390/jmmp8010010 - 04 Jan 2024
Abstract
►▼
Show Figures
Zr57Cu15Ni10Nb5 (more known as Vit-106) is a promising zirconium-based alloy with a high glass-forming ability, and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions
[...] Read more.
Zr57Cu15Ni10Nb5 (more known as Vit-106) is a promising zirconium-based alloy with a high glass-forming ability, and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome size limitations for BMGs because a workpiece is built by the addition of multiple melt portions in which the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on the partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of a Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.
Full article
Figure 1
Open AccessArticle
In-Process Machining Distortion Prediction Method Based on Bulk Residual Stresses Estimation from Reduced Layer Removal
J. Manuf. Mater. Process. 2024, 8(1), 9; https://doi.org/10.3390/jmmp8010009 - 03 Jan 2024
Abstract
Manufacturing structural monolithic components for the aerospace market often involves machining distortion, which entails high costs and material and energy waste in industry. Despite the development of distortion calculation and avoidance tools, this issue remains unsolved due to the difficulties in accurately and
[...] Read more.
Manufacturing structural monolithic components for the aerospace market often involves machining distortion, which entails high costs and material and energy waste in industry. Despite the development of distortion calculation and avoidance tools, this issue remains unsolved due to the difficulties in accurately and economically measuring the residual stresses of the machining blanks. In the last years, the on-machine layer removal method has shown its potential for industrial implementation, offering the possibility to obtain final components from blanks with measured residual stresses. However, this measuring method requires too long an implementation time to be used in-process as part of the manufacturing chains. In this sense, the objective of this paper is to provide a machining distortion prediction method based on bulk residual stress estimation and hybrid modelling. The bulk residual stresses estimation is performed using reduced layer removal measurements. Considering bulk residual stress data and machining-induced residual stress data, as well as geometry and material data, real-part distortion calculations can be performed. For this, a hybrid model based on the combination of an analytical formulation and finite element modelling is employed, which enables us to perform fast and accurate calculations. With the developments here presented, the machining distortion can be predicted, and its uncertainty range can be calculated, in a simple and fast way. The accuracy and practicality of these developments are evaluated by comparison with the experimental results, showing the capability of the proposed solution in providing distortion predictions with errors lower than 10% in comparison with the experimental results.
Full article
(This article belongs to the Special Issue Advances in Precision Machining Processes)
►▼
Show Figures
Figure 1
Open AccessArticle
Quality Prediction and Classification of Process Parameterization for Multi-Material Jetting by Means of Computer Vision and Machine Learning
by
, , , , and
J. Manuf. Mater. Process. 2024, 8(1), 8; https://doi.org/10.3390/jmmp8010008 - 01 Jan 2024
Abstract
►▼
Show Figures
Multi-Material Jetting (MMJ) is an additive manufacturing process empowering the printing of ceramics and hard metals with the highest precision. Given great advantages, it also poses challenges in ensuring the repeatability of part quality due to an inherent broader choice of built strategies.
[...] Read more.
Multi-Material Jetting (MMJ) is an additive manufacturing process empowering the printing of ceramics and hard metals with the highest precision. Given great advantages, it also poses challenges in ensuring the repeatability of part quality due to an inherent broader choice of built strategies. The addition of advanced quality assurance methods can therefore benefit the repeatability of part quality for widespread adoption. In particular, quality defects caused by improperly configured droplet overlap parameterizations, despite droplets themselves being well parameterized, constitute a major challenge for stable process control. This publication deals with the automated classification of the adequacy of process parameterization on green parts based on in-line surface measurements and their processing with machine learning methods, in particular the training of convolutional neural networks. To generate the training data, a demo part structure with eight layers was printed with different overlap settings, scanned, and labeled by process engineers. In particular, models with two convolutional layers and a pooling size of (6, 6) appeared to yield the best accuracies. Models trained only with images of the first layer and without the infill edge obtained validation accuracies of 90%. Consequently, an arbitrary section of the first layer is sufficient to deliver a prediction about the quality of the subsequently printed layers.
Full article
Figure 1
Open AccessArticle
Mesoscale Simulation of Laser Powder Bed Fusion with an Increased Layer Thickness for AlSi10Mg Alloy
by
, , , , , , , , , , , , and
J. Manuf. Mater. Process. 2024, 8(1), 7; https://doi.org/10.3390/jmmp8010007 - 01 Jan 2024
Abstract
Low performance is considered one of the main drawbacks of laser powder bed fusion (LPBF) technology. In the present work, the effect of the AlSi10Mg powder layer thickness on the laser melting process was investigated to improve the LPBF building rate. A high-fidelity
[...] Read more.
Low performance is considered one of the main drawbacks of laser powder bed fusion (LPBF) technology. In the present work, the effect of the AlSi10Mg powder layer thickness on the laser melting process was investigated to improve the LPBF building rate. A high-fidelity simulation of the melt pool formation was performed for different thicknesses of the powder bed using the Kintech Simulation Software for Additive Manufacturing (KiSSAM, version cd8e01d) developed by the authors. The powder bed after the recoating operation was obtained by the discrete element method. The laser energy deposition on the powder particles and the substrate was simulated by ray tracing. For the validation of the model, an experimental analysis of single tracks was performed on two types of substrates. The first substrate was manufactured directly with LPBF technology, while the second was cast. The simulation was carried out for various combinations of process parameters, predominantly with a high energy input, which provided a sufficient remelting depth. The calculations revealed the unstable keyhole mode appearance associated with the low absorptivity of the aluminum alloy at a scanning speed of 300 mm/s for all levels of the laser power (325–375 W). The results allowed formulating the criteria for the lack of fusion emerging during LPBF with an increased layer thickness. This work is expected to provide a scientific basis for the analysis of the maximum layer thickness via simulation to increase the performance of the technology.
Full article
(This article belongs to the Special Issue Advanced Welding Processes, Additive Manufacturing and Numerical Models)
►▼
Show Figures
Figure 1
Open AccessArticle
A Combined Microscopy Study of the Microstructural Evolution of Ferritic Stainless Steel upon Deep Drawing: The Role of Alloy Composition
J. Manuf. Mater. Process. 2024, 8(1), 6; https://doi.org/10.3390/jmmp8010006 - 01 Jan 2024
Abstract
►▼
Show Figures
Ferritic stainless steel (FSS) is widely used to manufacture deep-drawn products for corrosion resistance applications, being the alloy drawability strongly affected by its microstructural anisotropy. This study combines a variety of microscopy techniques enabling in-depth analyses of the microstructural evolution of two different
[...] Read more.
Ferritic stainless steel (FSS) is widely used to manufacture deep-drawn products for corrosion resistance applications, being the alloy drawability strongly affected by its microstructural anisotropy. This study combines a variety of microscopy techniques enabling in-depth analyses of the microstructural evolution of two different FSSs correlated to their deep drawing performance. One of the steels has a good correspondence with the standard EN-1.4016 (AISI 430). The other is a modified version of the previous one with higher contents of the ferrite-stabilising elements Si and Cr, and lower contents of the austenite-stabilising elements C, N, and Mn. Electron Backscatter Diffraction results confirm that the microstructural properties and drawability of FSS in the deep drawing process are improved in the modified steel version. Scanning transmission electron microscopy under low-angle annular dark field conditions evidences that the deformation mechanism of FSS during deep drawing follows a microstructural distortion model based on the grain size gradient and shows a variation of the deformation texture depending on the alloy composition. This work demonstrates the potential of advanced microscopy techniques for optimising the processing and design of ferritic stainless steels, with slight variations in the alloy composition, for deep drawing applications.
Full article
Graphical abstract
Open AccessArticle
Examining the Impact of Intermediate Cooling on Mechanical Properties of 22MnB5 in a Tailored Tempering Process
J. Manuf. Mater. Process. 2024, 8(1), 5; https://doi.org/10.3390/jmmp8010005 - 26 Dec 2023
Abstract
►▼
Show Figures
Tailoring the properties of hot-stamped components offers the potential to enhance crash performance while simultaneously improving downstream joining processes. In recent years, an innovative technology suited for achieving tailored properties involving the utilization of a specialized furnace chamber, known as the TemperBox®
[...] Read more.
Tailoring the properties of hot-stamped components offers the potential to enhance crash performance while simultaneously improving downstream joining processes. In recent years, an innovative technology suited for achieving tailored properties involving the utilization of a specialized furnace chamber, known as the TemperBox®, has been introduced. Within this chamber, a cooled aluminum mask shields specific areas of the blank from incoming heat radiation and concurrently absorbs the blank’s own radiation. The duration of the heat radiation exchange can influence the diffusion-dependent phase transformation and, consequently, the resulting mechanical properties. Hence, the intermediate cooling duration assumes a pivotal role as a parameter, as is investigated in this study. To examine the effects, specimens of the steel 22MnB5 AS150 are subjected to intermediate cooling of varying durations, followed by forming and partial quenching. The temperature profile of the blank during intermediate cooling prior to forming and quenching is analyzed. Subsequently, the tailored hot-stamped components are assessed for hardness, strength, ductility, and thickness strain. The study reveals that with increasing duration of partial intermediate cooling and targeted radiation exchange, a homogeneous ferritic–pearlitic structure is formed from an austenitic structure. This uniform structure of ferrite and pearlite is reflected in lower hardness and strength values, along with improved ductility. Additionally, this paper introduces a simulation methodology designed to calculate the dynamics of thermal radiation and the kinetics of phase transformation.
Full article
Figure 1
Open AccessArticle
Analysis of Machinability on Properties of Inconel 718 Wire and Arc Additive Manufacturing Products
J. Manuf. Mater. Process. 2024, 8(1), 4; https://doi.org/10.3390/jmmp8010004 - 25 Dec 2023
Abstract
►▼
Show Figures
Wire and arc additive manufacturing (WAAM) is a metal deposition technique with a fast rate and the possibility of a high volume of deposition. Because of its fast deposition and high heat input, the manufactured products have poor surface quality. This paper presents
[...] Read more.
Wire and arc additive manufacturing (WAAM) is a metal deposition technique with a fast rate and the possibility of a high volume of deposition. Because of its fast deposition and high heat input, the manufactured products have poor surface quality. This paper presents a study on the machining of Inconel 718 wall-shaped additive manufacturing (AM) products, a necessary step for the improvement of surface quality. Considering the possibility that the characteristics of the milling processes of AM products might differ from those of traditionally manufactured parts, in this research, two types of Inconel 718 were studied and compared: one was manufactured using WAAM, and the other was an Inconel 718 rolled bar (Aerospace Material Specifications 5662). Using the testing procedure, a conventional two-flute cutting tool was used to assess their machinability. For this process, multiple passes were performed at three different heights of the samples. Considering the peculiarities of the AM products, such as their uneven surfaces, dendritic microstructures, and anisotropy, the results were analyzed. After the machining operation, the effects on the products were also studied by analyzing their surface quality. This study found a higher stability in the cutting process for the AMS 5662 samples relative to the WAAM parts with less variability in the cutting forces overall, resulting in better surface quality.
Full article
Figure 1
Open AccessArticle
Numerical Modelling for Efficient Analysis of Large Size Multi-Stage Incremental Sheet Forming
J. Manuf. Mater. Process. 2024, 8(1), 3; https://doi.org/10.3390/jmmp8010003 - 22 Dec 2023
Abstract
Incremental sheet forming (ISF) is an advanced flexible manufacturing process to produce complex 3D products. Unlike the conventional stamping process, ISF does not require any high cost dedicated dies. However, numerical computation for large-size ISF processes is time-consuming, and its accuracy for spring
[...] Read more.
Incremental sheet forming (ISF) is an advanced flexible manufacturing process to produce complex 3D products. Unlike the conventional stamping process, ISF does not require any high cost dedicated dies. However, numerical computation for large-size ISF processes is time-consuming, and its accuracy for spring back due to unclamping tools after ISF cannot satisfy industrial demand. In this paper, an advanced numerical model considering complicated forming tool paths, trimming, and spring back was developed to efficiently simulate the multi-stage deformation phenomena of incremental sheet forming processes. Numerical modeling accuracy and efficiency are investigated considering the influence of tool path, material properties of the blank, mesh size, and boundary conditions. Through a series of case studies and comparisons with experimental results, it is observed that the numerical model with kinematics material properties and a moderate element size (5 mm) may reproduce the deformation characteristics of ISF with good accuracy and can obtain practical efficiency for a large-size ISF part.
Full article
(This article belongs to the Special Issue Advances in Material Forming)
►▼
Show Figures
Figure 1
Open AccessArticle
Three-Dimensional Printing of Biomass–Fungi Biocomposite Materials: The Effects of Mixing and Printing Parameters on Fungal Growth
J. Manuf. Mater. Process. 2024, 8(1), 2; https://doi.org/10.3390/jmmp8010002 - 19 Dec 2023
Abstract
►▼
Show Figures
Biomass–fungi biocomposite materials are derived from sustainable sources and can biodegrade at the end of their service. They can be used to manufacture products that are traditionally made from petroleum-based plastics. There are potential applications for these products in the packaging, furniture, and
[...] Read more.
Biomass–fungi biocomposite materials are derived from sustainable sources and can biodegrade at the end of their service. They can be used to manufacture products that are traditionally made from petroleum-based plastics. There are potential applications for these products in the packaging, furniture, and construction industries. In the biomass–fungi biocomposite materials, the biomass particles (made from agricultural waste such as hemp hurd) act as the substrate, and a network of fungal hyphae grow through and bind the biomass particles together. Typically, molding-based methods are used to manufacture products using these biocomposite materials. Recently, the authors reported a novel extrusion-based 3D printing method using these biocomposite materials. This paper reports a follow-up investigation into the effects of mixing parameters (mixing time and mixing mode) on fungal growth in biomass–fungi mixtures prepared for 3D printing and the effects of printing parameters (printing speed and extrusion pressure) on fungal growth in printed samples. The fungal growth was quantified using the number of fungal colonies that grew from samples. The results show that, when mixing time increased from 15 to 120 s, there was a 52% increase in fungal growth. Changing from continuous to intermittent mixing mode resulted in an 11% increase in fungal growth. Compared to mixtures that were not subjected to printing, samples printed with a high printing speed and high extrusion pressure had a 14.6% reduction in fungal growth, while those with a low printing speed and low extrusion pressure resulted in a 16.5% reduction in fungal growth.
Full article
Figure 1
Open AccessArticle
Picosecond Laser-Induced Bump Formation on Coated Glass for Smart Window Manufacturing
J. Manuf. Mater. Process. 2024, 8(1), 1; https://doi.org/10.3390/jmmp8010001 - 19 Dec 2023
Abstract
We report a study on the process of the formation of bubble-like structures on a coated glass surface using 50 ps laser pulses. The high-intensity interaction of laser radiation on the film–glass interface allowed us to develop a process for efficient glass bump
[...] Read more.
We report a study on the process of the formation of bubble-like structures on a coated glass surface using 50 ps laser pulses. The high-intensity interaction of laser radiation on the film–glass interface allowed us to develop a process for efficient glass bump formation. The high peak energy of the picosecond pulses has allowed us to merge the processes of coating evaporation and bubble growth into one. A parameter window was established within which efficient bump formation can be achieved. Well-defined spherical structures with a height up to 60 μm and a diameter up to 250 μm were obtained at pulse energy Epulse = 2.5 ÷ 4 μJ and laser fluence F = 2.5–0.41 J/cm2). The key aspects of the bump formation process were studied and are explained.
Full article
(This article belongs to the Special Issue Laser-Based Manufacturing II)
►▼
Show Figures
Figure 1
Open AccessArticle
Design, Configuration Synthesis, and Experimental Study of Side-Rolling Metamorphic Mechanism for Metal Additive Manufacturing
J. Manuf. Mater. Process. 2023, 7(6), 227; https://doi.org/10.3390/jmmp7060227 - 17 Dec 2023
Abstract
►▼
Show Figures
Arc additive manufacturing (AAM) has the advantages of fast deposition speed and good surfacing quality. It is a promising additive manufacturing (AM) method. However, arc additive manufacturing is difficult to use widely in industry due to its poor deformation, microstructure, and mechanical properties.
[...] Read more.
Arc additive manufacturing (AAM) has the advantages of fast deposition speed and good surfacing quality. It is a promising additive manufacturing (AM) method. However, arc additive manufacturing is difficult to use widely in industry due to its poor deformation, microstructure, and mechanical properties. Since the mechanical properties of materials can be greatly improved by rolling, a method for configuration synthesis of the side-rolling mechanism by using metamorphic mechanism theory is presented in this paper. Firstly, by analyzing the operational demands of the side-rolling mechanism, we obtained the motion cycle diagram for the metamorphic mechanism in addition to the corresponding equivalent resistance gradient matrix. Secondly, according to the motion cycle diagram and equivalent resistance gradient matrix of the metamorphic mechanism, the structure and constraint form of the metamorphic joints were established, and the relationship between the force variation and the structure and the constraint form of the metamorphic joints was also obtained. Then, the structures of all 12 corresponding constrained metamorphic mechanisms were synthesized. Ultimately, one among the twelve mechanisms was chosen as the side-rolling metamorphic mechanism. The topological transformation of its working configuration was examined. The results confirmed the feasibility and practicality of the proposed structural synthesis method in this study.
Full article
Figure 1
Open AccessArticle
Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy
by
, , , and
J. Manuf. Mater. Process. 2023, 7(6), 226; https://doi.org/10.3390/jmmp7060226 - 16 Dec 2023
Abstract
►▼
Show Figures
Ti6Al4V alloy (Ti64) is a popular material used in the aerospace, medical, and automotive industries due to its excellent mechanical properties. Laser Powder Bed Fusion (LPBF) is a promising manufacturing technique that can produce complex and net-shaped components with comparable mechanical properties to
[...] Read more.
Ti6Al4V alloy (Ti64) is a popular material used in the aerospace, medical, and automotive industries due to its excellent mechanical properties. Laser Powder Bed Fusion (LPBF) is a promising manufacturing technique that can produce complex and net-shaped components with comparable mechanical properties to those produced using conventional manufacturing techniques. However, during LPBF, the rapid cooling of the material can limit its ductility, making it difficult to achieve high levels of ductility while maintaining the required tensile strength for critical applications. To address this challenge, this study presents a novel approach to controlling the microstructure of Ti64 during LPBF by using a border design surrounding the main parts. It is hypothesized that the design induces in situ martensitic decomposition at different levels during the fabrication process, which can enhance the ductility of the material without compromising its tensile strength. To achieve this aim, a series of Ti64 samples were fabricated using LPBF with varying border designs, including those without borders and with gaps from 0.5 to 4 mm. The microstructure, composition, and mechanical properties of the Reference sample were compared with those of the samples fabricated with the surrounding border design. It was found that the latter had a more homogenized microstructure, a higher density, and improvements in both ductility and tensile strength. Moreover, it was discovered that the level of property improvement and martensitic transformation can be controlled by adjusting the gap space between the border and the main part, providing flexibility in the fabrication process. Overall, this study presents a promising approach for enhancing the mechanical properties of Ti64 produced via LPBF, making it more suitable for critical applications in various industries.
Full article
Figure 1
Open AccessArticle
A Thermo-Structural Analysis of Die-Sinking Electrical Discharge Machining (EDM) of a Haynes-25 Super Alloy Using Deep-Learning-Based Methodologies
by
, , , , and
J. Manuf. Mater. Process. 2023, 7(6), 225; https://doi.org/10.3390/jmmp7060225 - 13 Dec 2023
Abstract
The most effective and cutting-edge method for achieving a 0.004 mm precision on a typical material is to employ die-sinking electrical discharge machining (EDM). The material removal rate (MRR), tool wear rate (TWR), residual stresses, and crater depth were analyzed in the current
[...] Read more.
The most effective and cutting-edge method for achieving a 0.004 mm precision on a typical material is to employ die-sinking electrical discharge machining (EDM). The material removal rate (MRR), tool wear rate (TWR), residual stresses, and crater depth were analyzed in the current study in an effort to increase the productivity and comprehension of the die-sinking EDM process. A parametric design was employed to construct a two-dimensional model, and the accuracy of the findings was verified by comparing them to prior research. Experiments were conducted utilizing the EDM machine, and the outcomes were assessed in relation to numerical simulations of the MRR and TWR. A significant temperature disparity that arises among different sections of the workpiece may result in the formation of residual strains throughout. As a consequence, a structural model was developed in order to examine the impacts of various stress responses. The primary innovations of this paper are its parametric investigation of residual stresses and its use of Haynes 25, a workpiece material that has received limited attention despite its numerous benefits and variety of applications. In order to accurately forecast the output parameters, a deep neural network model, more precisely, a multilayer perceptron (MLP) regressor, was utilized. In order to improve the precision of the outcomes and guarantee stability during convergence, the L-BFGS solver, an adaptive learning rate, and the Rectified Linear Unit (ReLU) activation function were integrated. Extensive parametric studies allowed us to determine the connection between key inputs, including the discharge current, voltage, and spark-on time, and the output parameters, namely, the MRR, TWR, and crater depth.
Full article
(This article belongs to the Special Issue Advances in Metal Cutting and Cutting Tools)
►▼
Show Figures
Figure 1
Open AccessArticle
Wear of Carbide Plates with Diamond-like and Micro-Nano Polycrystalline Diamond Coatings during Interrupted Cutting of Composite Alloy Al/SiC
by
, , , , , , , , , and
J. Manuf. Mater. Process. 2023, 7(6), 224; https://doi.org/10.3390/jmmp7060224 - 08 Dec 2023
Abstract
►▼
Show Figures
The complexity of milling metal matrix composite alloys based on aluminum like Al/SiC is due to their low melting point and high abrasive ability, which causes increased wear of carbide tools. One of the effective ways to improve its reliability and service life
[...] Read more.
The complexity of milling metal matrix composite alloys based on aluminum like Al/SiC is due to their low melting point and high abrasive ability, which causes increased wear of carbide tools. One of the effective ways to improve its reliability and service life is to modify the surface by plasma chemical deposition of carbon-based multilayer functional layers from vapor (CVD) with high hardness and thermal conductivity: diamond-like (DLC) or polycrystalline diamond (PCD) coatings. Experiments on an indexable mill with CoroMill 200 inserts have shown that initial tool life increases up to 100% for cases with DLC and up to 300% for multilayered MCD/NCD films at a cutting speed of 800 m/min. The primary mechanism of wear of a carbide tool in this cutting mode was soft abrasion, when wear on both the rake and flank surfaces occurred due to the extrusion of cobalt binder between tungsten carbide grains, followed by their loss. Analysis of the wear pattern of plates with DLC and MCD/NCD coatings showed that abrasive wear begins to prevail against the background of soft abrasion. Adhesive wear is also present to a lesser extent, but there is no chipping of the base material from the cutting edge.
Full article
Figure 1
Open AccessArticle
Temperature and Wear Analysis of Adhesively Bonded and Soldered Cutting Tools for Woodcutting
by
and
J. Manuf. Mater. Process. 2023, 7(6), 223; https://doi.org/10.3390/jmmp7060223 - 06 Dec 2023
Abstract
Cutting tools undergo constant development to meet the demands of higher cutting speeds, difficult-to-cut materials and ecological considerations. One way to improve cutting tools involves transitioning from soldering to adhesive bonding in the manufacturing process. However, there is limited research comparing adhesively bonded
[...] Read more.
Cutting tools undergo constant development to meet the demands of higher cutting speeds, difficult-to-cut materials and ecological considerations. One way to improve cutting tools involves transitioning from soldering to adhesive bonding in the manufacturing process. However, there is limited research comparing adhesively bonded tools with soldered tools in woodcutting applications. This paper presents a comparison between adhesively bonded and soldered tools in the cutting of medium-density fiberboards over a cutting distance of 1000 m. The results indicate that adhesively bonded tools are well-suited for machining medium-density fiberboards. Additionally, the cutting-edge radii exhibit a slower increase and the tool temperatures are higher compared to soldered tools. Future research could optimize the damping effect through the precise design of the bonding area. Additionally, investigating a cooling concept for the machining process could help minimize ageing effects.
Full article
(This article belongs to the Special Issue Advances in Metal Cutting and Cutting Tools)
►▼
Show Figures
Figure 1
Open AccessArticle
Impact of Injection Molding Parameters on Material Acoustic Parameters
J. Manuf. Mater. Process. 2023, 7(6), 222; https://doi.org/10.3390/jmmp7060222 - 06 Dec 2023
Abstract
Understanding the relationship between injection molding parameters and the acoustic properties of polymers is crucial for optimizing the design and performance of acoustic-based polymer devices. In this work, the impact of injection molding parameters, such as the injection velocity and packing pressure, on
[...] Read more.
Understanding the relationship between injection molding parameters and the acoustic properties of polymers is crucial for optimizing the design and performance of acoustic-based polymer devices. In this work, the impact of injection molding parameters, such as the injection velocity and packing pressure, on the acoustic parameters of polymers, namely the elastic moduli, is studied. The measurements lead to calculating material parameters, such as the Young’s modulus and Poisson’s ratio, that can be swiftly measured and determined thanks to this method. Polymethyl methacrylate (PMMA) was used as the molding material, and using PMMA LG IG 840, the parts were simulated and injection molded, applying a ‘design of experiment’ (DOE) statistical method. The results indicated a correlation between the injection molding process parameters and the acoustic characteristics, such as the elastic moduli, and a specifically decreasing trend with increase in the injection velocity. Notably, a relative decrease in the Young’s modulus by was observed when increasing the packing pressure from to . Similarly, a decrease in the Poisson’s ratio of was observed when the injection velocity was increased from to . This method can be used to fine-tune the material properties according to the needs of a given application and to facilitate the characterization of different polymer acoustic properties essential for acoustic-based polymer devices.
Full article
(This article belongs to the Special Issue Advances in Injection Molding: Process, Materials and Applications)
►▼
Show Figures
Figure 1
Open AccessArticle
Dissimilar Friction Stir Lap Welding of Aluminium to Steel: Influence of Alloy Type and Sheet Thickness on Strain Distribution and Failure Location
J. Manuf. Mater. Process. 2023, 7(6), 221; https://doi.org/10.3390/jmmp7060221 - 06 Dec 2023
Abstract
Dissimilar joining through solid-state welding is an important engineering tool to address the transportation industry’s sustainable goals. The dissimilar friction stir lap welding (FSLW) of two different aluminium alloys (AA5182 and AA5052 with two different thicknesses) to steels AISI1010 and DP1000 was performed
[...] Read more.
Dissimilar joining through solid-state welding is an important engineering tool to address the transportation industry’s sustainable goals. The dissimilar friction stir lap welding (FSLW) of two different aluminium alloys (AA5182 and AA5052 with two different thicknesses) to steels AISI1010 and DP1000 was performed in this work, in order to analyse the effect of the mismatch in base material properties and plate thickness on the joint strength and fracture location. The mechanical behaviour and the strength of the welds were assessed using transverse tensile–shear testing and hardness measurements. Strain data acquisition through Digital Image Correlation (DIC) was used. The differences in fracture location registered for the different joints are explained based on the alloy’s plastic properties and on the mismatch in thickness between the plates. Local stress–strain curves were plotted, using the strain data acquired through DIC, to highlight the mechanisms resulting in the differences in tensile behaviour among the joints. It is concluded that despite the differences in failure location and tensile behaviour, the strength of the joints was very similar, irrespective of the base material combinations.
Full article
(This article belongs to the Special Issue Recent Developments in Friction Stir Welding Technology and Applications)
►▼
Show Figures
Figure 1
Highly Accessed Articles
Latest Books
E-Mail Alert
News
Topics
Topic in
Coatings, JMMP, Materials, Metals, Micromachines
Additive Manufacturing of Architected Metallic Materials
Topic Editors: Mohammad J. Mirzaali, Amir A. ZadpoorDeadline: 31 March 2024
Topic in
Coatings, JMMP, Materials, Metals, Processes
Alloys and Composites Corrosion and Mechanical Properties
Topic Editors: Jingxiang Xu, Zhenhua Chu, Xingwei ZhengDeadline: 15 April 2024
Topic in
Coatings, Materials, Metals, JMMP, Machines
Development of Friction Stir Welding and Processing
Topic Editors: Yongxian Huang, Li Zhou, Xiangchen Meng, Yuming XieDeadline: 31 May 2024
Topic in
Bioengineering, JMMP, Materials, Micromachines, Polymers
Advances in Filament Engineering for Biomaterials
Topic Editors: Ming-Wei Chang, Zeeshan Ahmad, Hui-Min David WangDeadline: 30 June 2024
Conferences
Special Issues
Special Issue in
JMMP
Advances in Welding Technology
Guest Editor: Paul KahDeadline: 31 January 2024
Special Issue in
JMMP
Advances in Metal Cutting and Cutting Tools
Guest Editors: Cristina M. Fernandes, Georgina Miranda, Joao Paulo DavimDeadline: 28 February 2024
Special Issue in
JMMP
Laser-Based Manufacturing II
Guest Editors: Antonio Riveiro, Rafael ComesañaDeadline: 1 April 2024
Special Issue in
JMMP
Industry 4.0: Manufacturing and Materials Processing
Guest Editor: Yashar JavadiDeadline: 30 April 2024