Search Results (4,287)

Sodium hypochlorite (NaClO) is widely used for the chemical cleaning of fouled ultrafiltration (UF) membranes. Various studies performed on polymeric membranes demonstrate that long-term (>100 h) exposure to NaClO deteriorates the physicochemical properties of the membranes, leading to reduced performance and service life. However, the effect of NaClO cleaning on ceramic membranes, particularly the number of cleaning cycles they can undergo to alleviate irreversible fouling, remains poorly understood. Silicon carbide (SiC) membranes have garnered widespread attention for water and wastewater treatment, but their chemical stability in NaClO has not been studied. Low-pressure chemical vapor deposition (LP-CVD) provides a simple and economical route to prepare/modify ceramic membranes. As such, LP-CVD facilitates the preparation of SiC membranes: (a) in a single step; and (b) at much lower temperatures (700–900 °C) in comparison with sol-gel methods (ca. 2000 °C). In this work, SiC ultrafiltration (UF) membranes were prepared via LP-CVD at two different deposition temperatures and pressures. Subsequently, their chemical stability in NaClO was investigated over 200 h of aging. Afterward, the properties and performance of as-prepared SiC UF membranes were evaluated before and after aging to determine the optimal deposition conditions. Our results indicate that the SiC UF membrane prepared via LP-CVD at 860 °C and 100 mTorr exhibited excellent resistance to NaClO aging, while the membrane prepared at 750 °C and 600 mTorr significantly deteriorated. These findings not only highlight a novel preparation route for SiC membranes in a single step via LP-CVD, but also provide new insights about the careful selection of LP-CVD conditions for SiC membranes to ensure their long-term performance and robustness under harsh chemical cleaning conditions. Full article

Patterned membrane surfaces offer a hydrodynamic approach to mitigating concentration polarization and subsequent surface fouling. However, when subjected to steady crossflow conditions, surface patterns promote particle accumulation in the recirculation zones of cavity-like spaces. In order to resolve this issue, we numerically subject a two-dimensional, patterned membrane surface to a rapidly pulsed crossflow. When combined with cavity-like spaces, such as the valleys of membrane surface patterns, a rapidly pulsed flow generates mixing mechanisms (i.e., the deep sweep and the vortex ejection) and disrupts recirculation zones. In only four pulses, we demonstrate the ability of these mechanisms to remove over half of the particles trapped in recirculation zones via massless particle tracking studies (i.e., numerical integration of the simulated velocity field). The results of this work suggest that when combined with a rapidly pulsed inlet flow, patterned membrane surfaces can not only alleviate concentration polarization and the surface fouling that follows but also reduce the need for traditional cleaning methods that require operational downtime and often involve the use of abrasive chemical agents. Full article

This article considers a theoretical analysis of the influence of the main coupled effects and spacers on the transfer of salt ions in electromembrane systems (EMS) using a 2D mathematical model of the transfer process in a desalting channel with spacers based on boundary value problems for the coupled system of Nernst–Planck–Poisson and Navier–Stokes equations. The basic patterns of salt ion transport have been established, taking into account diffusion, electromigration, forced convection, electroconvection, dissociation/recombination reactions of water molecules, as well as spacers located inside the desalting channel. It has been shown that spacers and taking into account the dissociation/recombination reaction of water molecules significantly change both the formation and development of electroconvection. This article confirms the fact of the exaltation of the limiting current studied by Harkatz, where it is shown that the current (flux) of salt ions increases when the dissociation reaction begins by a certain value called the exaltation current, which is proportional to the flow of water dissociation products. A significant combined effect of electroconvection and dissociation/recombination reactions as well as the spacer system in the desalting channel on the transport of salt ions are shown. The complex, nonlinear, and non-stationary interaction of all the main effects of concentration polarization and spacers in the desalting channel are also considered in the work. Full article

This study investigated the influence of various plasticizers commonly used in the manufacture of polymer inclusion membranes (PIMs), such as 2-nitrophenyl octyl ether (NPOE), phthalates, adipates, and sebacates on the mechanical, thermal, and transport properties of membranes. Additionally, butyl stearate (BTS), chosen for its non-toxic nature compared to phthalates and its cost-effectiveness relative to adipates and sebacates, was evaluated as a plasticizer in PIMs for the first time. All plasticizers were incorporated in PIMs made of either cellulose triacetate (CTA) or poly(vinyl chloride) (PVC) as the base polymers and the task-specific ionic liquid trioctylmethylammonium thiosalicylate (TOMATS) as the carrier. The plasticizers were found to significantly affect the characteristics of membrane hydrophilicity, mechanical flexibility, and thermal stability. Transport experiments using Hg(II) as a model target ion revealed that, for CTA-based PIMs, the plasticizer did not significantly affect transport efficiency. However, for PVC-based PIMs, BTS exhibited better efficiency when compared to NPOE. These findings highlight the potential of BTS as an attractive alternative to currently used plasticizers in PVC-based PIM formulations. Full article

Cannabidiol (CBD), the non-psychoactive compound derived from the cannabis plant, has gained attention in recent years as a remedy against gastrointestinal disorders ranging from nausea and inflammation to abdominal pain. Recent advances demonstrated an effect on inflammatory pathways and barrier proteins. However, information on possible direct effects is scarce and needs to be addressed, as applications are currently increasing in popularity. To accomplish this, we have employed Xenopus laevis oocytes as a heterologous expression system for analysis of the direct effects on stomach-specific claudins and further developed tight junction (TJ) protein interaction assays. Human claudin-4, claudin-5, and claudin-18.2 were expressed in Xenopus oocytes, clustered in pairs to form contact areas, and analyzed in a two-cell model approach, including measurement of the contact area and contact strength. CLDN4/5/18 + CLDN4/5/18 oocyte pairs were incubated with 20 µM CBD or with 40 µM CBD and were compared to cells without CBD treatment (ctrl). For interaction analysis, the contact area was measured after 24 h and 48 h. Whereas CBD did not affect the size of the protein interaction area, Double Orbital Challenge experiments revealed an increased contact strength after 24 h incubation with CBD. In addition, the Xenopus oocyte experiments were accompanied by an analysis of claudin-4, -5, and -18 expression in gastric epithelium by immunoblotting and immunohistochemistry. Claudin-4, -5, and -18 were strongly expressed, indicating a major role for gastric epithelial barrier function. In summary, our study shows direct effects of 40 µM CBD on Xenopus oocytes heterologously expressing a stomach-specific claudin combination, indicating a supportive and beneficial effect of CBD on gastric TJ proteins. Full article

Novel composite membranes employing a poly(ether-block-amide) (PEBAX) copolymer and sulfonated montmorillonite (S-MMT) as a filler were developed. The ratio of polyether to polyamide blocks was investigated using PEBAX 2533 and PEBAX 4533 based on the membrane properties and performance. Additionally, the effect of the changing filler ratio was monitored. The interaction between the S-MMT as nanofiller and the polymer matrix of PEBAX2533 and PEBAX4533 as well as the crystalline nature and thermal and mechanical stability of the composite membranes were evaluated using Fourier Transform Infrared Spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and tensile test. The composite membrane with 7 wt.% S-MMT showed the highest water uptake of 21% and 16% and an acceptable swelling degree of 16% and 9% for PEBAX 2533 and PEBAX 4533 composite membranes, respectively. In terms of water uptake and ion exchange capacity at room temperature, the new un-protonated membranes are superior to un-protonated Nafion. Meanwhile, with the same S-MMT content, the ion conductivity of PEBAX 2533 and PEBAX 4533 composite membranes is 2 and 1.6 mS/cm, and their ion exchange capacity is 0.9 and 1.10 meq/g. Full article

In this study, all-cellulose nanocomposite (ACNC) was successfully prepared through a green and sustainable approach by using corn stalk as raw material, water as regeneration solvent, and recyclable two-component ionic liquid/DMSO as the solvent to dissolve cellulose. The morphology and structural properties of ACNC were determined by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction analysis, indicating homogeneity and good crystallinity. In addition, a comprehensive characterization of ACNC showed that CNF not only improved the thermal stability and mechanical characteristics of ACNC, but also significantly improved the oxygen barrier performance. The ACNC prepared in this work has a good appearance, smooth surface, and good optical transparency, which provides a potential application prospect for converting cellulose wastes such as corn straws into biodegradable packaging materials and electronic device encapsulation materials. Full article

The dense packing of opposite cytoplasmic surfaces of the lipid-enriched myelin membrane, responsible for the proper saltatory conduction of nerve impulses through axons, is ensured by the adhesive properties of myelin basic protein (MBP). Although preferentially interacting with negatively charged phosphatidylserine (PS) lipids, as an intrinsically disordered protein, it can easily adapt its shape to its immediate environment and thus adsorb to domains made of zwitterionic phosphatidylcholine (PC) lipids. As the molecular-level interaction pattern between MBP and PC lipid membranes suffers from scarce characterization, an experimental and computational study of multilamellar liposomes (MLVs) composed of 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) in the presence of bovine MBP is presented here. Calorimetric and temperature-dependent UV-Vis measurements identified DPPC pretransition temperature (T_p) and calorimetric enthalpy (ΔH_cal) as the physicochemical parameters most responsive to the presence of MBP. Besides suggesting an increase in β-sheet fractions of structured MBP segments as DPPC lipids undergo from the gel (20 °C) to the fluid (50 °C) phase, FTIR spectra unraveled the significant contribution of lysine (Lys) residues in the adsorption pattern, especially when DPPC is in the fluid (50 °C) phase. In addition to highlighting the importance of Lys residues in the MBP adsorption on DPPC lipid bilayer, employing salt bridges (SBs) and hydrogen bonds (HBs), MD data suggest the crucial importance of the orientation of MBP with respect to the surface of the DPPC lipid bilayer. Full article

Over half of the pharmaceutical industry’s capital investments are related to the purification of active pharmaceutical ingredients (APIs). Thus, a cost-effective purification process with a highly concentrated solution is urgently required. In addition, the purification process should be nonthermal because most APIs and their intermediates are temperature-sensitive. This study investigated a high-degree concentration organic solvent forward osmosis (OSFO) membrane process. A polyketone-based thin-film composite hollow fiber membrane with a polyamide selective layer on the bore surface was used as the OSFO membrane to achieve a high tolerance for organic solvents and an effective concentration. MeOH, sucrose octaacetate (SoA), and 2M polyethylene glycol 400 (PEG-400)/MeOH solution were used as the solvent, model API, and a draw solution (DS), respectively. OSFO was performed at room temperature (23 ± 3 °C). Consequently, the 11 wt% SoA/MeOH solution was concentrated to 52 wt% without any SoA leakage into the DS. To our knowledge, there are no studies in which up to a 5 wt% concentration by OSFO has been demonstrated. However, the final feed solution contained 17 wt% PEG-400. This study demonstrates the promising potential of OSFO for pharmaceutical pre-concentration and the technical problems that need to be solved for social implementation. Full article

4-Nitroaniline (4NA) is a common organic pollutant that is released into the environment during the manufacture and processing of a wide variety of industrial products. This article describes the use of an emulsion liquid membrane process to remove 4NA from aqueous solutions using a type 1 facilitated transport mechanism. Optimization of the removal process was carried out by analyzing the efficiency of 4NA removal from the feed phase and the initial apparent feed/membrane fluxes and permeabilities under different experimental conditions. The kinetics of the removal process was analyzed using a simplified mass transfer model involving an empirical mass transfer coefficient calculated from experimental data, assuming that the concentrations of 4NA in the external aqueous phase and in the internal w/o emulsion are uniform. The results show that there is a very good fit between the experimental and model data and that the variation in the values of the overall mass transfer coefficients with the experimental conditions coincides with that of the removal efficiency mentioned above. The transport mechanism was studied by identifying the rate-controlling step of the removal process, using models described for adsorption processes, due to the strong parallelism between the transport mechanisms in adsorption and emulsion liquid membrane processes. Full article

The demand for natural products in the treatment of dermatological pathologies has boosted the use of bioactive substances such as lavender essential oil (LEO), which stands out for its anti-inflammatory and antioxidant properties and its antimicrobial potential. Biopolymers such as chitosan (CHT) and alginate (ALG) are biodegradable and biocompatible and have proven their viability in biomedical applications such as skin regeneration. The inhibitory effect of LEO on the growth of skin-related bacterial species Staphylococcus aureus, Staphylococcus epidermidis, Pseudomonas aeruginosa and the fungus Candida albicans was studied by incorporating 1% v/v LEO encapsulated in CHT, ALG, and CHT/ALG membranes. Despite the verification of the antimicrobial effect of all type of membranes, no synergistic effect was observed following the addition of LEO. S. aureus and P. aeruginosa showed the most growth on the different substrates and C. albicans demonstrated the highest inhibition. This is a first approach using microorganisms isolated from clinical samples or skin microbiota. Further investigation would be advisable using more clinical strains for each microorganism to validate their biomedical applicability. Full article

The aim of this research is to develop new nanocomposite membranes (NMs) for guided bone regeneration from polycaprolactone (PCL), with different concentrations of gentamicin sulfate (GEN) and nano-hydroxyapatite (nHAP) through electrospinning. The obtained NMs were characterized for structure through SEM and AFM, which revealed the influence of GEN and nHAP on the fiber diameter. The addition of GEN lowered the fiber diameter, and the addition of nHAP increased the diameter of the fibers. The NMs demonstrated antibacterial properties against P. aeruginosa, S. aureus, B. cereus, and E. coli depending on the drug concentration, while being negligibly affected by the nHAP content. NM cytotoxicity assessment, performed once using the MTT assay, revealed no cytotoxicity. The developed NMs could be a promising alternative for guided bone regeneration. Full article

The Gram-negative bacterium Helicobacter pylori is a very successful pathogen, one of the most commonly identified causes of bacterial infections in humans worldwide. H. pylori produces several virulence factors that contribute to its persistence in the hostile host habitat and to its pathogenicity. The most extensively studied are cytotoxin-associated gene A (CagA) and vacuolating cytotoxin A (VacA). VacA is present in almost all H. pylori strains. As a secreted multifunctional toxin, it assists bacterial colonization, survival, and proliferation during long-lasting infections. To exert its effect on gastric epithelium and other cell types, VacA undergoes several modifications and crosses multiple membrane barriers. Once inside the gastric epithelial cell, VacA disrupts many cellular-signaling pathways and processes, leading mainly to changes in the efflux of various ions, the depolarization of membrane potential, and perturbations in endocytic trafficking and mitochondrial function. The most notable effect of VacA is the formation of vacuole-like structures, which may lead to apoptosis. This review focuses on the processes involved in VacA secretion, processing, and entry into host cells, with a particular emphasis on the interaction of the mature toxin with host membranes and the formation of transmembrane pores. Full article

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide–polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques including XPS, FTIR, SEM, TGA, and zeta potential analysis are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment. Full article

A 40 cm length Bis(triethoxysilyl)ethane (BTESE) membrane having different pore sizes was successfully prepared by changing the number of coating times for gas permeation (GP) and organic solvent reverse osmosis (OSRO) separation study. It was found that BTESE-6 membranes prepared through six-time coating consisted of small-sized pores in the range 0.56 to 0.64 nm estimated using modified Gas Translation (mGT) method and 0.59 to 0.67 nm estimated by nanopermporometry (NPP) method, respectively. These membranes demonstrated a high DMF rejection, R_DMF > 95% with total flux, J_{v total} > 5 kg m⁻² h⁻¹ at operating condition feed pressure, P_f: 8 MPa; feed temperature, T_f : 50 °C; and feed flowrate, Q_f : 30 mL/min; and they exhibited a high degree selectivity of He/SF₆ in the range of ~ 260–3400 at a permeation temperature 200 °C. On the other hand, the larger pore sizes of the BTESE-4 membranes (pore size estimates > 0.76 nm to 1.02 nm) exhibited low DMF rejection and a low degree selectivity of He/SF₆ around ~30% and 25, respectively, at the same operating condition as BTESE-6. Both GT and NPP methods can be considered as an indicator of the measurement membrane pore size. From this study, it was found that He and SF₆ gases can be some of the potential predictors for water and DMF permeance. Furthermore, by comparing our OSRO membrane with other PV membranes for DMF/H₂O separation, our BTESE-6 membranes still exhibited high flux in the range of 3–6 kg m⁻² h⁻¹ with a separation factor H₂O/DMF in the range of 80–120. Full article