Search Results (32)

This paper presents a low-voltage CMOS four-stage amplifier operating in the subthreshold region. The first design technique includes the cross-feedforward positive feedback frequency compensation (CFPFC) for obtaining better bandwidth efficiency in a low-voltage multi-stage amplifier. The second design technique incorporates both the bulk-drain-driven input stage topology in conjunction with a low-voltage attenuator to permit operation at a low voltage, and improves the input common-mode range (ICMR). The proposed circuit is implemented using TSMC-40 nm process technology. It consumes 0.866 μW at a supply voltage of 0.5 V. With a capacitive load of 50 pF, this four-stage amplifier can achieve 84.59 dB in gain, 161.00 kHz in unity-gain bandwidth, 96 deg in phase margin, and 5.7 dB in gain margin whilst offering an input-referred noise of 213.63 $\mathrm{n}\mathrm{V}/\sqrt{\mathrm{H}\mathrm{z}}$ @1 kHz, small-signal power-bandwidth FoM_ss of 9.31 (MHz∙pF/μW), and noise-power per bandwidth-based FoM_npb of 1.15 × 10⁻⁶ (($\mathrm{\mu }\mathrm{V}/\sqrt{\mathrm{H}\mathrm{z}}$)·µW/Hz). Compared to the conventional bulk-driven input stage design technique, it offers improved multi-parameter performance metrics in terms of noise, power, and bandwidth at a compromising tradeoff on ICMR with respect to bulk-driven amplifier design. Compared with conventional gate-source input stage design, it offers improved ICMR. The amplifier is useful for low-voltage analog signal-processing applications. Full article

Different winner-take-all (WTA) and loser-take-all (LTA) circuits are studied, and their operations are analyzed in this review. The exclusive operation of the current conveyor, binary tree, and time-domain WTA/LTA architectures, as the most important architectures reported in the literature, are compared from the perspectives of power consumption, speed, and precision. Full article

In recent years, the development of Advanced Driver-Assistance Systems (ADASs) is driving the need for more reliable and precise on-vehicle sensing. Radar and lidar are crucial in this framework, since they allow sensing of vehicle’s surroundings. In such a scenario, it is necessary to master these sensing systems, and knowing their similarities and differences is important. Due to ADAS’s intrinsic real-time performance requirements, it is almost mandatory to be aware of the processing algorithms required by radar and lidar to understand what can be optimized and what actions can be taken to approach the real-time requirement. This review aims to present state-of-the-art radar and lidar technology, mainly focusing on modulation schemes and imaging systems, highlighting their weaknesses and strengths. Then, an overview of the sensor data processing algorithms is provided, with some considerations on what type of algorithms can be accelerated in hardware, pointing to some implementations from the literature. In conclusion, the basic concepts of sensor fusion are presented, and a comparison between radar and lidar is performed. Full article

5G Cell Search (CS) is the first step for user equipment (UE) to initiate communication with the 5G node B (gNB) every time it is powered ON. In cellular networks, CS is accomplished via synchronization signals (SS) broadcasted by gNB. 5G 3rd generation partnership project (3GPP) specifications offer a detailed discussion on the SS generation at gNB, but a limited understanding of their blind search and detection is available. Unlike 4G, 5G SS may not be transmitted at the center of carrier frequency, and their frequency location is unknown to UE. In this work, we demonstrate the 5G CS by designing 3GPP compatible hardware realization of the physical layer (PHY) of the gNB transmitter and UE receiver. The proposed SS detection explores a novel down-sampling approach resulting in a 60% reduction in on-chip memory and 50% lower search time. Via detailed performance analysis, we analyze the functional correctness, computational complexity, and latency of the proposed approach for different word lengths, signal-to-noise ratio (SNR), and down-sampling factors. We demonstrate end-to-end 5G CS using GNU Radio-based RFNoC framework on the USRP-FPGA platform and achieve 66% faster SS search compared to software. The 3GPP compatibility and demonstration on hardware strengthen the commercial significance of the proposed work. Full article

Silicon carbide is changing power electronics; it is enabling massive car electrification owing to its far more efficient operation with respect to mainstream silicon in a large variety of energy conversion systems like the main traction inverter of an electric vehicle (EV). Its superior performance depends upon unique properties such as lower switching and conduction losses, safer high-temperature operation and high-voltage capability. Starting briefly with a description of its physics, more detailed information is then given about some key manufacturing steps such as crystal growth and epitaxy. Afterwards, an overview of its inherent defects and how to mitigate them is presented. Finally, a typical EV’s propulsion inverter is shown, proving the technology’s effectiveness in meeting requirements for mass electrification. Foreword: In recent years, SiC has drawn the attention of a growing number of power electronics designers as the material has good prospects for reducing environmental impacts on a global basis. The goal of this paper, based on the author’s contribution to the introduction of the technology at STMicroelectronics, is to show the potential of silicon carbide in enabling massive car electrification. The company’s SiC MOSFETs, tailored to the automotive industry, are enabling visionary EV makers to pave the way for sustainable e-mobility. The intent of this paper is to describe, for a large crowd of readers, how SiC features can accelerate such a transition by quantifying the benefits they bring in terms of improved efficiency in an EV electric powertrain. The paper also has the ambition to highlight the material’s physics and to give an overview of its production processes, starting from the crystal growth for realizing substrates to the main epitaxy techniques. Some space has been devoted to the analysis of the main crystal defects not present in silicon and whose nature poses new challenges in terms of manufacturing yields and screening. Finally, some insights into the market evolution and on the transition to 200 mm wafers are given. Full article

In this paper, we propose a Virtual Prototype (VP) driven verification methodology for Hardware (HW) peripherals. In particular, we combine two approaches that complement each other and use the VP as a readily available reference model: We use (A) Coverage-Guided Fuzzing (CGF) which enables comprehensive verification at the unit-level of the Register-Transfer Level (RTL) HW peripheral with a Transaction Level Modeling (TLM) reference, and (B) an application-driven co-simulation-based approach that enables verification of the HW peripheral at the system-level. As a case-study, we utilize a RISC-V Platform Level Interrupt Controller (PLIC) as HW peripheral and use an abstract TLM PLIC implementation from the open source RISC-V VP as the reference model. In our experiments we find three behavioral mismatches and discuss the observation of these, as well as non-functional timing behavior mismatches, that were found through the proposed synergistic approach. Furthermore, we provide a discussion and considerations on the RTL/TLM Transactors, as they embody one keystone in cross-level methods. As the different approaches uncover different mismatches in our case-study (e.g., behavioral mismatches and timing mismatches), we conclude a synergy between the methods to aid in verification efforts. Full article

This work is focused on the performance of three different standard-cell-based comparator topologies, considering ultra-low-voltage (ULV) operation. The main application scenarios in which standard-cell-based comparators can be exploited are considered, and a set of figures of merit (FoM) to allow an in-depth comparison among the different topologies is introduced. Then, a set of simulation testbenches are defined in order to simulate and compare the considered topologies implemented in both a 130 nm technology and a 28 nm FDSOI CMOS process. Propagation delay, power consumption and power–delay product are evaluated for different values of the input common mode voltage, as a function of input differential amplitude, and in different supply voltage and temperature conditions. Monte Carlo simulations to evaluate the input offset voltage under mismatch variations are also provided. Simulation results show that the performances of the different comparator topologies are strongly dependent on the input common mode voltage, and that the best values for all the performance figures of merit are achieved by the comparator based on three-input NAND gates, with the only limitation being its non-rail-to-rail input common mode range (ICMR). The performances of the considered comparator topologies have also been simulated for different values of the supply voltage, ranging from 0.3 V to 1.2 V, showing that, even if standard-cell-based comparators can be operated at higher supply voltages by scaling their performances accordingly, the best values of the FoMs are achieved for $V_{DD}$ = 0.3 V. Full article

For Convolutional Neural Networks (CNNs), Depthwise Separable CNN (DSCNN) is the preferred architecture for Application Specific Integrated Circuit (ASIC) implementation on edge devices. It benefits from a multi-mode approximate multiplier proposed in this work. The proposed approximate multiplier uses two 4-bit multiplication operations to implement a 12-bit multiplication operation by reusing the same multiplier array. With this approximate multiplier, sequential multiplication operations are pipelined in a modified DSCNN to fully utilize the Processing Element (PE) array in the convolutional layer. Two versions of Approximate-DSCNN (A-DSCNN) accelerators were implemented on TSMC 40 nm CMOS process with a supply voltage of 0.9 V. At a clock frequency of 200 MHz, the designs achieve 4.78 GOPs/mW and 4.89 GOP/mW power efficiency while occupying 1.16 mm${}^2$ and 0.398 mm${}^2$ area, respectively. Full article

In contemporary devices, the number and diversity of sensors is increasing, thus, requiring both efficient and robust interfacing to the sensors. Implementing the interfacing systems in advanced integration technologies faces numerous issues due to manufacturing deviations, signal swings, noise, etc. The interface sensor designers escape to the time domain and digital design techniques to handle these challenges. Biology gives examples of efficient machines that have vastly outperformed conventional technology. This work pursues a neuromorphic spiking sensory system design with the same efficient style as biology. Our chip, that comprises the essential elements of the adaptive neuromorphic spiking sensory system, such as the neuron, synapse, adaptive coincidence detection (ACD), and self-adaptive spike-to-rank coding (SA-SRC), was manufactured in XFAB CMOS 0.35 $\mathsf{\mu }$m technology via EUROPRACTICE. The main emphasis of this paper is to present the measurement outcomes of the SA-SRC on-chip, evaluating the efficacy of its adaptation scheme, and assessing its capability to produce spike orders that correspond to the temporal difference between the two spikes received at its inputs. The SA-SRC plays a crucial role in performing the primary function of the adaptive neuromorphic spiking sensory system. The measurement results of the chip confirm the simulation results of our previous work. Full article

This paper presents a state-of-the-art review of different approaches for Neural Architecture Search targeting resource-constrained devices such as microcontrollers, as well as the implementations of on-device learning techniques for them. Approaches such as MCUNet have been able to drive the design of tiny neural architectures with low memory and computational requirements which can be deployed effectively on microcontrollers. Regarding on-device learning, there are various solutions that have addressed concept drift and have coped with the accuracy drop in real-time data depending on the task targeted, and these rely on a variety of learning methods. For computer vision, MCUNetV3 uses backpropagation and represents a state-of-the-art solution. The Restricted Coulomb Energy Neural Network is a promising method for learning with an extremely low memory footprint and computational complexity, which should be considered for future investigations. Full article

This paper presents a practical implementation and measurement results of power-efficient chip performance optimization, utilizing low-cost indirect measurement methods to support self-X properties (self-calibration, self-healing, self-optimization, etc.) for in-field optimization of analog front-end sensory electronics with XFAB 0.35 µm complementary metal oxide semiconductor (CMOS) technology. The reconfigurable, fully differential indirect current-feedback instrumentation amplifier (CFIA) performance is intrinsically optimized by employing a single test sinusoidal signal stimulus and measuring the total harmonic distortion (THD) at the output. To enhance the optimization process, the experience replay particle swarm optimization (ERPSO) algorithm is utilized as an artificial intelligence (AI) agent, implemented at the hardware level, to optimize the performance characteristics of the CFIA. The ERPSO algorithm extends the selection producer capabilities of the classical PSO methodology by incorporating an experience replay buffer to mitigate the likelihood of being trapped in local optima. Furthermore, the CFIA circuit has been integrated with a simple power-monitoring module to assess the power consumption of the optimization solution, to achieve a power-efficient and reliable configuration. The optimized chip performance showed an approximate 34% increase in power efficiency while achieving a targeted THD value of −72 dB, utilizing a 1 Vp-p differential input signal with a frequency of 1 MHz, and consuming approximately 53 mW of power. Preliminary tests conducted on the fabricated chip, using the default configuration pattern extrapolated from post-layout simulations, revealed an unacceptable performance behavior of the CFIA. Nevertheless, the proposed in-field optimization successfully restored the circuit’s performance, resulting in a robust design that meets the performance achieved in the design phase. Full article

Silicon radiation detectors, a special type of microelectronic sensor which plays a crucial role in many applications, are reviewed in this paper, focusing on fabrication aspects. After addressing the basic concepts and the main requirements, the evolution of detector technologies is discussed, which has been mainly driven by the ever-increasing demands for frontier scientific experiments. Full article

Content-addressable memory (CAM) has been part of the memory market for more than five decades. CAM can carry out a single clock cycle lookup based on the content rather than an address. Thanks to this attractive feature, CAM is utilized in memory systems where a high-speed content lookup technique is required. However, typical CAM applications only support exact matching, as opposed to approximate matching, where a certain Hamming distance (several mismatching characters between a query pattern and the dataset stored in CAM) needs to be tolerated. Recent interest in approximate search has led to the development of new CAM-based alternatives, accelerating the processing of large data workloads in the realm of big data, genomics, and other data-intensive applications. In this review, we provide an overview of approximate CAM and describe its current and potential applications that would benefit from approximate search computing. Full article

This paper reviews the state of the art on bandpass $\Sigma \Delta$ modulators (BP-$\Sigma \Delta$Ms) intended to digitize radio frequency (RF) signals. A priori, this is the most direct way to implement software-defined radio (SDR) systems since the analog/digital interface is placed closer to the antenna, thus reducing the analog circuitry and doing most of the signal processing in the digital domain. In spite of their higher programmability and scalability, RF BP-$\Sigma \Delta$M analog-to-digital converters (ADCs) require more energy to operate in the GHz range as compared with their low-pass (LP) counterparts. This makes conventional direct conversion receivers (DCRs) the commonplace approach due to their overall smaller energy consumption. This paper surveys some circuits and systems techniques which can make RF ADCs and SDR-based transceivers more efficient and feasible to be embedded in mobile terminals. Full article

This paper presents a design methodology for a low-power, low-chip-area, and high-resolution successive approximations register (SAR) analog-to-digital converter (ADC). The proposed method includes a segmented capacitive DAC (C-DAC) to reduce the power consumption and the total area. An embedded self-calibration algorithm based on a set of trimming capacitors was applied alongside a dynamic element matching (DEM) procedure to control the inherent linearity issues caused by the process mismatch. The SAR ADC and each additional algorithm were modeled in MATLAB to show their efficiency. Finally, a simple methodology was developed to allow for the fast estimation of signal-to-noise ratios (SNRs) without any FFT calculation. Full article