Search Results (93)

Magnetostrictive alloys hold great promise for Energy Harvesting applications due to their inherent durability. However, their implementation often results in usable voltage ranges that fall significantly below common electronic standards like 1.6, 3.3, and 5 volts. Consequently, the utilization of electronic circuits becomes essential to amplify the voltage and enhance energy conversion efficiency. Over the past few decades, numerous conversion techniques have been devised for other intelligent materials, such as piezoelectrics, some of which have even made their way into commercial products. Surprisingly, there is a dearth of specialized techniques, if not a complete absence, tailored to magnetostrictive devices. Among potential solutions, a suitable AC–DC Boost converter stands out as a highly promising candidate for addressing this challenge, but this solution has never been fully characterized. Then, this paper presents thorough experimental validations of such a converter, driven by a real-time Arduino board equipped to measure source time periods and operate under various conditions. We present several cases demonstrating the circuit’s substantial potential for enhancing energy harvesting from magnetostrictive materials. Full article

Photovoltaic (PV) systems are widely adopted for renewable energy generation, but their performance is influenced by complex interactions between longer-term trends and seasonal variations. This study aims to remove these factors and provide valuable insights for optimising PV system operation. We employ comprehensive datasets of measured PV system performance over five years, focusing on identifying the distinct contributions of longer-term trends and seasonal effects. To achieve this, we develop a novel analytical framework that combines time series and statistical analytical techniques. By applying this framework to the extensive performance data, we successfully break down the overall PV system output into its constituent components, allowing us to find out the impact of the system degradation, maintenance, and weather variations from the inherent seasonal patterns. Our results reveal significant trends in PV system performance, indicating the need for proactive maintenance strategies to mitigate degradation effects. Moreover, we quantify the impact of changing weather patterns and provide recommendations for optimising the system’s efficiency based on seasonally varying conditions. Hence, this study not only advances our understanding of the intricate variations within PV system performance but also provides practical guidance for enhancing the sustainability and effectiveness of solar energy utilisation in both residential and commercial settings. Full article

In this paper, a long short-term memory (LSTM)-based method with a multi-input tensor approach is used for the classification of events that affect the power quality (PQ) in power systems with distributed generation sources. The considered events are line faults (one line, two lines, and three lines faulted), islanding events, sudden load variations, and generation tripping. The proposed LSTM-based method was trained and tested using the signals produced by the events simulated in a study system with distributed generation sources via PSCAD^®. Then, noise with different levels was added to the testing set for a thorough assessment, and the results were compared with other well-known methods such as convolutional and simple recurrent neuronal networks. The LSTM-based method with multi-input proved to be effective for event classification, achieving remarkable classification performance even in noisy conditions. Full article

The dynamics of electrical systems have changed significantly with the increasing penetration of non-conventional loads such as hydrogen electrolysers. As a result, detailed investigations are required to quantify and characterize these loads’ effects on the dynamic response of interconnected synchronous machines after being subjected to a disturbance. Many studies have focused on the effects of conventional static and dynamic loads. However, the impact of hydrogen electrolysers on the stability of power systems’ rotor angles is rarely studied. This paper assesses the effect of proton exchange membrane (PEM) electrolysers on small-disturbance rotor-angle stability. Dynamic modelling and the control of a PEM electrolyser as a load are first studied to achieve this. Then, the proposed electrolyser model is tested in the Amercoeur plant, which is part of the Belgian power system, to study its effect on the small-signal rotor-angle stability. Two approaches are considered to examine this impact: an analytical approach and time-domain simulations. The analytical approach consists of establishing a state-space model of the Belgian test system through linearisation around an operating point of the non-linear differential and the algebraic equations of the synchronous generators, the PEM electrolyser, the loads, and the network. The obtained state-space model allows for the determination of the eigenvalues, which are useful to evaluate the effect of the PEM electrolyser on the small-signal rotor-angle stability. This impact is investigated by examining the movement of the eigenvalues in the left complex half-plane. The obtained results show that the PEM electrolyser affects the electromechanical modes of synchronous machines by increasing their oscillation frequencies. The results also show that the effect of the electrolyser on these modes can be improved by adjusting the inertial constant and the damping coefficient of the synchronous machines. These results are consolidated through time-domain simulations using the software Matlab/Simscape from the version MatlabR2022a-academic use from Mathworks. Full article

In recent years, deep reinforcement learning (DRL) has garnered substantial attention in the context of enhancing resilience in power and energy systems. Resilience, characterized by the ability to withstand, absorb, and quickly recover from natural disasters and human-induced disruptions, has become paramount in ensuring the stability and dependability of critical infrastructure. This comprehensive review delves into the latest advancements and applications of DRL in enhancing the resilience of power and energy systems, highlighting significant contributions and key insights. The exploration commences with a concise elucidation of the fundamental principles of DRL, highlighting the intricate interplay among reinforcement learning (RL), deep learning, and the emergence of DRL. Furthermore, it categorizes and describes various DRL algorithms, laying a robust foundation for comprehending the applicability of DRL. The linkage between DRL and power system resilience is forged through a systematic classification of DRL applications into five pivotal dimensions: dynamic response, recovery and restoration, energy management and control, communications and cybersecurity, and resilience planning and metrics development. This structured categorization facilitates a methodical exploration of how DRL methodologies can effectively tackle critical challenges within the domain of power and energy system resilience. The review meticulously examines the inherent challenges and limitations entailed in integrating DRL into power and energy system resilience, shedding light on practical challenges and potential pitfalls. Additionally, it offers insights into promising avenues for future research, with the aim of inspiring innovative solutions and further progress in this vital domain. Full article

A significant electromotive force is induced in the rotor circuit of a doubly fed induction generator (DFIG) due to its high vulnerability to grid faults. Therefore, the system performance must be increased with appropriate control actions that can successfully offset such abnormalities in order to provide consistent and stable operations during grid disturbances. In this regard, this paper presents a solution based on a combination of an energy storage-based crowbar and a rotor-side crowbar that makes the effective transient current and voltage suppression for wind-driven DFIG possible. The core of the solution is its ability to restrict the transient rotor and stator overcurrents and DC-link overvoltages within their prescribed limits, thereby protecting the DFIG and power converters and improving the system’s ability to ride through faults. Further, the capacity of an energy storage device for transient suppression is estimated. The results confirmed that the proposed approach not only kept the transient rotor and stator currents within ±50% of their respective rated values in severe system faults but also limited the DC-link voltage variations under ±15% of its rated value, achieving transient control objectives precisely and maintaining a stable grid connection during the faults. Full article

The ever-increasing number of plug-in electric vehicles (PEVs) requires appropriate electric vehicle grid integration (EVGI) for charging coordination to maintain grid stability and enhance PEV user convenience. As such, the widespread adoption of electric mobility can be successful. EVGI is facilitated through charging stations and empowers PEV users to manage their charging demand by using smart charging solutions. This makes PEV grids assets that provide flexibility to the power grid. The Internet of Things (IoT) feature can make smooth EVGI possible through a supporting communication infrastructure. In this regard, the selection of an appropriate communication protocol is essential for the successful implementation of EVGI. This study assesses the efficacy of the UK’s 4G network with TCP and 4G UDP protocols for potential EVGI operations. For this, an EVGI emulation test bed is developed, featuring three charging parking lots with the capacity to accommodate up to 64 PEVs. The network’s performance is assessed in terms of data packet loss (e.g., the data-exchange capability between EVGI entities) and latency metrics. The findings reveal that while 4G TCP often outperforms 4G UDP, both achieve latencies of less than 1 s with confidence intervals of 90% or greater for single PEV cases. However, it is observed that the high penetration of PEVs introduces a pronounced latency due to queuing delays in the network including routers and the base station servers, highlighting the challenges associated with maintaining efficient EVGI coordination, which in turn affects the efficient use of grid assets. Full article

This paper introduces a novel power supply voltage adjustment strategy that can determine the optimum voltage value based on the amount of absorbed power. The novel automatic voltage adjustment technique was called inverse maximum power point tracking (iMPPT). The proposed control strategy consists of a modified maximum power point tracking (MPPT) algorithm (more precisely the P&O method). In this case, the modified MPPT technique establishes the minimum value of the input absorbed power of a consumer load served by a switched-mode power supply (SMPS). The iMPPT adjusts the input power by modifying the input voltage of the main power supply. The served loads are connected to the variable power supply via an interfacing power electronics converter that performs the automatic voltage regulation function (AVR). The optimal value of the input voltage level can be achieved when the input power of the automatic voltage regulation converter is at a minimum. In that case, the energy conversion efficiency ratio is at a maximum, and the overall losses related to the front-end power stage are at a minimum. The proposed technique can also be considered a Maximum Efficiency Tracking (MET) method. By performing the inverse operation of a maximum power point tracking algorithm on the input demanded power of a switched mode power supply (SMPS), the optimum input voltage level can be determined when the maximum energy conversion ratio (related to a given load level) is achieved. The novel proposed iMPPT method can improve the energy conversion ratio from 85% up to approximately 10% in the case of an output power level of 800 W served by a synchronous buck converter at the input voltage level of 350 V. The total amount of recovered power in this situation can be approximately 100 W. Full article

Power system transformation can unleash wide-ranging effects across multiple, frequently interlinked dimensions such as the environment, economy, resource systems, and biodiversity. Consequently, assessing the multidimensional impacts of power system transformation, especially under rapid transitions, has become increasingly important. Nonetheless, there is a gap in the literature when it comes to applying such an analysis to a Mediterranean country facing structural socioeconomic challenges. This paper explores the potential multifaceted implications of rapidly decarbonizing the Greek power sector by 2035, focusing on the local-level consequences. The evaluation criteria encompass the cost-optimal power mix, power costs, land use, biomass utilization, GDP, and employment. In this effort, a technology-rich cost optimization model representing Greece’s power sector is linked to a global Computable General Equilibrium (CGE) macroeconomic model focusing on the Greek economy. The results indicate that a fast decarbonization of the Greek power sector could trigger positive socioeconomic consequences in the short- and medium-term (GDP: +1.70, employees: +59,000 in 2030), although it may induce negative long-term socioeconomic effects due to increased capital investment requirements. Additionally, the impact on land use may only be trivial, with the potential to decrease over time due to the de-escalation of biomass power generation, thereby reducing the risk of harming biodiversity. Full article

The battery-based multilevel inverter has grown in popularity due to its ability to boost a system’s safety while increasing the effective battery life. Nevertheless, the system’s high degree of freedom, induced by a large number of switches, provides difficulties. In the past, central computation systems that needed extensive communication between the master and the slave module on each cell were presented as a solution for running such a system. However, because of the enormous number of slaves, the bus system created a bottleneck during operation. As an alternative to conventional multilevel inverter systems, which rely on a master–slave architecture for communication, decentralized controllers represent a feasible solution for communication capacity constraints. These controllers operate autonomously, depending on local measurements and decision-making. With this approach, it is possible to reduce the load on the bus system by approximately 90 percent and to enable a balanced state of charge throughout the system with an absolute maximum standard deviation of $1.1\times {10}^{-5}$. This strategy results in a more reliable and versatile multilevel inverter system, while the load on the bus system is reduced and more precise switching instructions are enabled. Full article

Recently, the danger of a long blackout is discussed in Europe. Blackouts can be caused by failures in the energy distribution, errors in large power plants or even cyber-attacks. This can lead to a chain reaction and a disintegration of the mains. Longer blackouts have an extreme impact on the economy as a whole and on local households. Therefore, a small local grid at home which can supply the most important loads over some time has garnered increasing interest. With a small direct current (DC) grid, critical loads such as for deep freezers and refrigerators can be supplied, and some LED lights can be used in the evening or at night. Solar generators (panels) can be used to charge energy storage devices, e.g., batteries. A DC grid can not only be used in the case of an emergency, but can also be used to reduce energy consumption out of the public mains and reduce energy bills. The architecture of the household emergency DC grid is discussed; suggestions for batteries are given; two simple chargers, based on DC-DC-converters like the Buck (step-down) and on the Boost (step-up) converters, are shown; dimensioning suggestions are given; and simple, robust controllers, a P-controller with disturbance feedforward and a hysteresis controller, are treated and tested via simulations. The goal of the paper is to show a simple autonomous home energy system without an external fieldbus, LAN or internet connection with special focus on simple charger topologies. Full article

We have developed a conventional benchmark model for the prediction of two days of electricity consumption for industrial and institutional customers of an electricity provider. This task of predicting 96 values of 15 min of electricity consumption per day in one shot is successfully dealt with by a dynamic regression model that uses the Seasonal and Trend decomposition method (STL) for the estimation of the trend and the seasonal components based on (approximately) three years of real data. With the help of suitable R packages, our concept can also be applied to comparable problems in electricity consumption prediction. Full article

This paper investigates the potential of bidirectional charging using modular multilevel inverter-based reconfigurable battery systems via grid-parallel control. The system offers several advantages such as modularity, scalability, and fault-tolerance over conventional battery electric vehicle systems. It is designed for seamless integration with the grid, allowing bidirectional power flow and efficient energy storage. Within this study, the battery system is first simulated in Matlab/Simulink and later implemented into a hardware setup. Eventually, the simulation results and the measurements have been compared and evaluated. Thereby, startup sequences and constant current scenarios were investigated. It has been shown that the system is fully capable to charge and discharge the batteries in the grid-parallel connection, thus enabling bidirectional charging with close to full drive system power. The current total harmonic distortion complies with grid regulations and can potentially improve the grid quality. The proposed system offers significant potential for grid-integrated energy storage systems, addressing the challenges associated with renewable energy integration, grid stability, and energy management. In comparison to other publications on this topic, the proposed approach does not need additional dedicated power electronic hardware and has more degrees of freedom for current control. Full article

Wide-Area Power System Stabilizers (WAPSSs) are damping controllers used in power systems that employ data from Phasor Measurement Units (PMUs). WAPSSs are capable of providing high damping rates for the low-frequency oscillation modes, especially the inter-area modes. Oscillation modes can destabilize power systems if they are not correctly identified and adequately damped. However, WAPSS communication channels may be subject to failures or cyber-attacks that affect their proper operation and may even cause system instability. This research proposes a method based on an optimization model for the design of a WAPSS robust to multiple permanent communication failures. The results of applications of the proposed method in the IEEE 68-bus system show the ability of the WAPSS design to be robust to a possible number of permanent communication failures. Above this value, the combinations of failures and processing time are high and they make it difficult to obtain high damping rates for the closed-loop control system. The application and comparison of different optimization techniques are valid and showed a superior performance of the Grey Wolf Optimizer in solving the optimization problem. Full article